Zuvo Docs

Guide

Enabling MCP Server Access

Configure secure access to the MCP server in your self-hosted Zuvo instance.

The MCP (Model Context Protocol) server in self-hosted Zuvo runs behind the internal API. Currently, it does not offer OAuth 2.1 authentication, and is not intended to be exposed to the Internet. The corresponding API route has to be protected by restricting network connections from the outside. By default, all connections to the MCP server are denied.

This guide explains how to securely enable access to your self-hosted MCP server.

Security considerations

Accessing via SSH tunnel

Step 1: Determine the local IP address that will be used to access the MCP server

When connecting via an SSH tunnel to the Studio Docker container, the source IP will be that of the Docker bridge gateway. You need to allow connections from this IP address.

Envoy

Determine the Docker bridge gateway IP on the host running your Zuvo containers:

docker inspect supabase-envoy \
  --format '{{range .NetworkSettings.Networks}}{{println .Gateway}}{{end}}'
Kong

Determine the Docker bridge gateway IP on the host running your Zuvo containers:

docker inspect supabase-kong \
  --format '{{range .NetworkSettings.Networks}}{{println .Gateway}}{{end}}'

This command will output an IP address, e.g., 172.18.0.1.

Step 2: Allow connections from the gateway IP

Envoy

Add the IP address you discovered to the Envoy configuration by editing the /mcp route in ./volumes/api/envoy/lds.template.yaml:

  1. Find the route with prefix: /mcp
  2. Comment out the rbac block that denies all traffic and uncomment the allow-list policy below
  3. Keep loopback entries (127.0.0.1 and ::1) and add your Docker bridge gateway IP
  4. Preserve the existing indentation - YAML is whitespace-sensitive and the config will fail to load if it changes
  5. Your edited configuration should look like the example below:
- match:
    prefix: /mcp
  route:
    cluster: studio
    prefix_rewrite: /api/mcp
    timeout: 30s
  request_headers_to_add:
    - header:
        key: X-Forwarded-Prefix
        value: /mcp
      append_action: ADD_IF_ABSENT
  typed_per_filter_config:
    envoy.filters.http.basic_auth:
      '@type': >-
        type.googleapis.com/envoy.config.route.v3.FilterConfig
      disabled: true
    envoy.filters.http.rbac:
      '@type': >-
        type.googleapis.com/envoy.extensions.filters.http.rbac.v3.RBACPerRoute
      # Block access to /mcp by default
      #rbac:
      #  rules:
      #    action: DENY
      #    policies:
      #      deny_all:
      #        permissions:
      #          - any: true
      #        principals:
      #          - any: true
      # Enable local access (danger zone!)
      # 1. Comment out the 'rbac' block above.
      # 2. Uncomment and adjust the 'rbac' block below.
      # 3. Add or adjust your local IPs in 'principals'.
      rbac:
        rules:
          action: ALLOW
          policies:
            allow_local:
              permissions:
                - any: true
              principals:
                - direct_remote_ip:
                    address_prefix: 127.0.0.1
                    prefix_len: 32
                - direct_remote_ip:
                    address_prefix: ::1
                    prefix_len: 128
                - direct_remote_ip:
                    # Add your Docker bridge gateway IP below
                    address_prefix: 172.18.0.1
                    prefix_len: 32
Kong

Add the IP address you discovered to the Kong configuration by editing the following section in ./volumes/api/kong.yml:

  1. Comment out the request-termination section
  2. Remove the # symbols from the entire section starting with - name: cors, including deny: []
  3. Add your local IP to the 'allow' list
  4. Preserve the existing indentation - YAML is whitespace-sensitive and the config will fail to load if it changes
  5. Your edited configuration should look like the example below:
## MCP endpoint - local access
- name: mcp
  _comment: 'MCP: /mcp -> http://studio:3000/api/mcp (local access)'
  url: http://studio:3000/api/mcp
  routes:
    - name: mcp
      strip_path: true
      paths:
        - /mcp
  plugins:
    # Block access to /mcp by default
    #- name: request-termination
    #  config:
    #    status_code: 403
    #    message: "Access is forbidden."
    # Enable local access (danger zone!)
    # 1. Comment out the 'request-termination' section above
    # 2. Uncomment the entire section below, including 'deny'
    # 3. Add your local IPs to the 'allow' list
    - name: cors
    - name: ip-restriction
      config:
        allow:
          - 127.0.0.1
          - ::1
          # Add your Docker bridge gateway IP below
          - 172.18.0.1
        # Do not remove deny!
        deny: []

Step 3: Restart API gateway

After you've added the local IP address as above, restart your gateway:

sh run.sh restart api-gw

Step 4: Create the SSH tunnel

From your local machine, create an SSH tunnel to your Zuvo host:

ssh -L localhost:8080:localhost:8000 you@your-supabase-host

This command forwards local port 8080 to port 8000 on your Zuvo host.

Step 5: Configure your MCP client

Edit the settings for your MCP client and add the following to "mcpServers": {} or "servers": {}:

{
  "mcpServers": {
    "supabase-self-hosted": {
      "url": "http://localhost:8080/mcp"
    }
  }
}

Step 6: Start using the self-hosted MCP server

From your local machine, check that the MCP server is reachable:

curl http://localhost:8080/mcp \
  -X POST \
  -H "Content-Type: application/json" \
  -H "Accept: application/json, text/event-stream" \
  -H "MCP-Protocol-Version: 2025-06-18" \
  -d '{
    "jsonrpc": "2.0",
    "id": 1,
    "method": "initialize",
    "params": {
      "protocolVersion": "2025-06-18",
      "capabilities": {
        "elicitation": {}
      },
      "clientInfo": {
        "name": "test-client",
        "title": "Test Client",
        "version": "1.0.0"
      }
    }
  }'

Start your MCP client (Claude Code, Cursor, etc.) and verify access to the MCP tools. For example, you can ask: "What is Zuvo anon key? Use the Zuvo MCP server tools."

Troubleshooting

If you are unable to connect to the MCP server:

  1. Confirm the Docker bridge gateway IP is correctly added to the API gateway configuration
  2. Check the API gateway's logs for errors: docker compose logs api-gw
  3. Make sure your SSH tunnel is active